|
The Planer /Thicknesser
Used for the basic operations.
Planing a face on a rough or distorted wood, squaring an edge against
that face, and then thicknessing another face and edge parallel to
the originals.
The Planer
The first thing you'll notice when
approaching a surface planer is that it predominantly consists of a
surface table, a rotating cutting cylinder (traditionally with two or
three blades) and an adjustable side fence (normally set at 90 degree
to the surface table).
The workpiece is slowly pushed
along the table towards the cutting cylinder, whilst pressing against
the side fence for guidance. The cutting blades will remove the
unwanted wood from the workpiece (not normally more than 3mm in one
pass). It is important that the wood is fed in slowly, done
correctly, and a flat surface is produced.
However if the feed speed is too
high, it is possible that an undesired ripping effect is created. It
may be necessary to feed the work through more than once depending
upon the initial distortion.
Once a flat surface is obtained, it
can now be used as a reference face to form the other three surfaces.
This flat surface is pressed against the side fence, and the
operation repeated to form a second surface (or edge) square to the
original.
The Thicknesser
The Thicknesser enables the
operator to pass wood under the same cutter cylinder used by the
planer.The thicknesser table is adjusted to the desired height
beneath the cylinder, so that when the previously planed surface of
wood is moved along it, the blades cut down to the set calibrated
height, producing a constant thickness.
This thicknessing process is
usually motor driven, and roller in the machine allow the wood to be
self fed along the thicknessing table at the correct speed.
 |
|
|
ITEM No:
01344 - Woodworking |
|
|
10" x 6" Planer / Thicknesser |
|
|
• |
Speedy
conversion from planer to thicknesser - Complete
convinience and reduced downtime |
|
• |
Dust
Extraction Facility - Superp
for waste extraction, reducing airborne dust for health and safety,
and minimising clean up time on completion. |
|
• |
Mode
interlock switch - Prevents
incorrect operation of planer mode when set up in thicknesser mode,
and vice versa, prolonging machiene life
|
• |
Magnetic NVR
switch - For
added safety |
|
• |
Large
precision machiened adjustable work table - For
accurate planing |
|
• |
Fully
adjustable planing fence - Allows
accurate planing from 90º down to 45º |
|
|
• |
Calibrated
thicknesser scale - For
precission and ease in use |
|
• |
Anti kick
back lock - Safety
against re-coiling wood |
|
• |
Rubber
outfeed roller - Protects
workpiece against marking |
|
• |
Thicknesser
table supported by four interlinked threaded rods -
Giving rigid support in operation, reducing the risk of dipping when
working with a heavy wood section. |
|
• |
Two year
warrenty - For
extra peace of mind |
|
• |
Legs included |
|
• |
Mobile stand
available - Order
SIP code 01346 |
|
• |
Blades:
Double Edged Blades - Order SIP
code 01338
Resharpenable Blades - Order SIP
code 01339
Wheel Kit - Order SIP code 01346 |
|
|
MODEL |
10" x
6" Planer Thicknesser |
|
|
|
|
ITEM Nº |
01344 |
|
VOLTAGE |
230 V |
|
MOTOR |
2000 W (22.75 Hp) |
|
MAXIMUM WORKING WIDTH MM |
260 |
|
MAXIMUM DEPTH OF CUT (PLANING) MM |
3 |
|
THICKNESSER HEIGHT CAPACITY MM |
160 |
|
DIAMETER OF CUTTER BLOCK MM |
63 |
|
CUTTER BLOCK KNIVES |
2 |
|
CUTTER BLOCK SPEED RPM |
6500 |
|
THICKNESSER FEED RATE M/MIN |
5 |
|
MAXIMUM FENCE TILT |
45º |
|
OVERALL LENGTH OF TABLES MM |
1000 |
|
LEGNTH OF THICKNESSER BED MM |
400 |
|
PLANER TABLE HEIGHT MM |
840 |
|
NET WEIGHT KG |
66.5 |
|
PACKAGED WEIGHT KG |
73 |
|
PACKAGED DIMENSIONS MM |
710 X 570 X 560 |
|
